2016 Subaru Outback Rear Brake Pad Replacement with Electronic Parking
Replacing the rear brake pads on a 2016 Subaru Outback with an electronic parking brake can be a daunting task if you’re not familiar with the process. However, with the right tools and a little bit of patience, you should be able to do this job yourself and save some money in the process.
Getting Started: Safety First
Before you start, it’s important to take some safety precautions. Make sure your car is parked on a level surface and that the parking brake is engaged. Chock the wheels to prevent the car from rolling. It’s also a good idea to wear safety glasses and gloves.
Step 1 – Disable the Electronic Parking Brake
The first step is to disable the electronic parking brake. You can do this by following the instructions in your owner’s manual. On most models, you’ll need to insert the key into the ignition and turn it to the “On” position, then press the brake pedal and pull the parking brake release lever.
Step 2 – Remove the Rear Wheels
Once the electronic parking brake is disabled, you can remove the rear wheels. To do this, loosen the lug nuts on each wheel, then use a jack to lift the car up. Once the wheel is off the ground, remove the lug nuts and take the wheel off.
Step 3 – Remove the Brake Caliper
The next step is to remove the brake caliper. To do this, you’ll need to remove the two bolts that hold the caliper in place. Once the bolts are removed, you can carefully lift the caliper off of the rotor. Be careful not to damage the brake hose.
Step 4 – Remove the Old Brake Pads
Once the brake caliper is removed, you can remove the old brake pads. To do this, simply pull them out of the caliper. The pads may be held in place by a spring clip. If so, you’ll need to use a screwdriver to remove the clip.
Step 5 – Install the New Brake Pads
The next step is to install the new brake pads. To do this, simply slide them into the caliper. Make sure that the pads are installed in the correct orientation. The pads will have a chamfered edge that should face the rotor.
Step 6 – Reinstall the Brake Caliper
Once the new brake pads are installed, you can reinstall the brake caliper. To do this, simply lift the caliper over the rotor and secure it with the two bolts. Tighten the bolts until they are snug, but do not overtighten them.
Step 7 – Reinstall the Rear Wheels
Once the brake calipers are reinstalled, you can reinstall the rear wheels. To do this, simply lift the wheel onto the hub and tighten the lug nuts. Once the lug nuts are tightened, lower the car to the ground and torque the lug nuts to the specified torque.
Step 8 – Enable the Electronic Parking Brake
The final step is to enable the electronic parking brake. To do this, follow the instructions in your owner’s manual. On most models, you’ll need to insert the key into the ignition and turn it to the “On” position, then press the brake pedal and push the parking brake release lever.
There You have it! You have now successfully replaced the rear brake pads on your 2016 Subaru Outback with electronic parking.
Tips and Expert Advice
Here are a few tips and expert advice that will help you replace the rear brake pads on your 2016 Subaru Outback with electronic parking:
- Make sure you have the right tools for the job. You’ll need a jack, a lug wrench, a socket wrench, and a screwdriver.
- Follow the instructions in your owner’s manual carefully.
- Be careful not to damage the brake hose when you’re removing the brake caliper.
- Make sure that the new brake pads are installed in the correct orientation.
- Torque the lug nuts to the specified torque.
FAQs on Replacing Rear Brake Pads on 2016 Subaru Outback with Electronic Parking
- Q: What tools do I need to replace the rear brake pads on my 2016 Subaru Outback with electronic parking?
- A: You’ll need a jack, a lug wrench, a socket wrench, and a screwdriver.
- Q: What precautions should I take before starting the job?
- A: Make sure your car is parked on a level surface and that the parking brake is engaged. Chock the wheels to prevent the car from rolling. It’s also a good idea to wear safety glasses and gloves.
- Q: How do I disable the electronic parking brake?
- A: On most models, you’ll need to insert the key into the ignition and turn it to the “On” position, then press the brake pedal and pull the parking brake release lever.
Conclusion
Replacing the rear brake pads on a 2016 Subaru Outback with electronic parking is not a difficult job. By following the instructions in this article, you can do this job yourself and save some money in the process.
Is replacing your car’s brake pads something you’re interested in learning more about? What other topics related to car maintenance and repair would you like to know more about?
